 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| D200RP Series Short Circuit Protected Regulated, 2W SIP DC/DC Converters Electrical Specifications Specifications typical @ +25C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Key Features: 2W Output Power Short Circuit Protection Tight Line/Load Regulation 1,000 VDC Isolation Miniature SIP Case >1.5 MHour MTBF 15 Standard Models Parameter Input Voltage Range Input Filter Reverse Polarity Input Current Conditions 5 VDC Input 12 VDC Input 24 VDC Input Min. 4.5 10.8 21.6 Typ. 5.0 12.0 24.0 Max. 5.5 13.2 26.4 0.3 Units VDC (Pi) Filter A Units % % % mV P - P % 0.02 Continuous Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 1,000 1,000 60 40 Conditions Ambient Case Min. -25 -25 -40 Free Air Convection RH, Non-condensing 95 % Typ. +25 Max. +71 +85 +125 Typ. Max. Units VDC M pF kHz Units C C C %/C Output Parameter Output Voltage Accuracy Line Regulation Load Regulation (Note 1) Ripple & Noise (20 MHz) (Note 2) Output Power Protection Temperature Coefficient Output Short Circuit 120 For Vin Min to Max Conditions Min. Typ. Max. 2.0 0.5 0.5 75 General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Environmental Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity MicroPower Direct 232 Tosca Drive Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Physical Case Size Case Material Weight 1.26 x 0.32 x 0.55 Inches (32.0 x 8.0 x 14.0 mm) Non-Conductive Black Plastic (UL94-V0) 0.17 Oz (4.8g) Conditions MIL HDBK 217F, 25C, Gnd Benign Conditions 5 VDC Input Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation 12 VDC Input 24 VDC Input 1.5 mm From Case For 10 Sec All Models Min. 1.5 Min. -0.7 -0.7 -0.7 Typ. Max. 9.0 18.0 30.0 260 450 C mW VDC Typ. Max. Units MHours Units Reliability Specifications Parameter MTBF Absolute Maximum Ratings Parameter Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number D201RP D202RP D203RP D204RP D205RP D211RP D212RP D213RP D214RP D215RP D221RP D222RP D223RP D224RP D225RP Notes: Input Voltage (VDC) Current (mA) Nominal Range Full-Load No-Load 5 4.5 - 5.5 606 80 5 4.5 - 5.5 606 80 5 4.5 - 5.5 571 80 5 4.5 - 5.5 571 80 5 4.5 - 5.5 588 80 12 10.8 - 13.2 253 45 12 10.8 - 13.2 253 45 12 10.8 - 13.2 238 45 12 10.8 - 13.2 238 45 12 10.8 - 13.2 246 45 24 21.6 - 26.4 130 25 24 21.6 - 26.4 130 25 24 21.6 - 26.4 122 25 24 21.6 - 26.4 122 25 24 21.6 - 26.4 118 25 Voltage (VDC) 5.0 9.0 12.0 15.0 24.0 5.0 9.0 12.0 15.0 24.0 5.0 9.0 12.0 15.0 24.0 Output Current (mA, Max) 400.0 222.0 167.0 133.0 83.0 400.0 222.0 167.0 133.0 83.0 400.0 222.0 167.0 133.0 83.0 Current (mA, Min) 40.0 22.0 17.0 13.0 10.0 40.0 22.0 17.0 13.0 10.0 40.0 22.0 17.0 13.0 10.0 Efficiency (%, Typ) 66 66 70 70 68 66 66 70 70 68 64 64 68 68 70 Fuse Rating Slow-Blow (mA) 1,000 1,000 1,000 1,000 1,000 500 500 500 500 500 200 200 200 200 200 1. Output load regulation is specified for a load change of 20% to 100%. 2. When measuring output ripple, it is recommended that an external 0.33 F ceramic capacitor be placed from the +Vout pin to the -Vout pin. 3. Operation at no-load will not damage these units. However, they may not meet all specifications. 4. These do not require external components to operate, but the use of a low ESR capacitor (approximately 10 uF, ESR <1.0 at 100 kHz) mounted close to the converter input pins is recommended. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Derating Curve Capacitive Load F Max 470 Pin Connections Pin 1 2 3 9 10 11 12 Function +Vin NC NC NC -Vout +Vout -Vin Mechanical Dimensions NC: No Connection Notes: All dimensions are typical in inches (mm) Tolerance x.xx = 0.01 (0.25) Pin 1 is marked by a "dot" or indentation on the side of the unit MicroPower Direct www.micropowerdirect.com 232 Tosca Drive Stoughton, MA 02072 TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: sales@micropowerdirect.com |
Price & Availability of D211RP
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |